The Introduction of PPS R7

 

PPS R7 is a chemical produced by Phillips high-performance polyphenylene sulfide, has good dimensional stability, excellent chemical resistance and high temperature performance. PPS has a 30-year-old has become recognized worldwide, there are strict requirements on the plastic of choice, is widely used in automotive, electronics, industrial, household appliances.
Advantages:
Continuous use temperature of 240 ℃, short-term use temperature can reach 270 ℃; its flame retardant (UL94: V-0, a number of levels can be achieved 5VA); excellent chemical resistance and oxidation resistance; very rigid; very low The absorption rate; Even at high temperature creep resistance is also very good; inch Stability: excellent creep resistance, low coefficient of linear expansion, high temperature dimensional stability is also very good; forming: liquidity, and can be thin-wall molding may be the same as other glass reinforced plastics for molding.
Typical application:
Household appliances: hair dryers, curly hair, microwave ovens and cooker parts, popular for many years.; Electrical and electronic industry (plug, multi-point connectors, bobbins, relays, switches, electronic vitality packaging, capacitors and transistors with different types of design of the computer connector AGP, BGA and PLCC, etc., especially for the need for co-SMT (Surface mount techonology) products)
Industrial products: motors, pumps, valves, lights cups and other products, too numerous to mention.
PPS in the automobile industry mainly on the application of high temperature, corrosion, requiring precision molding parts. Such as: pumps and accessories, all kinds of sensor parts, engine parts, lamp parts, all kinds of pipes and valves. Temperature resistant parts and other various parts.
PPS in the electronic, electrical industry, the main applications are: temperature fuse box, relay parts, coil axis connectors, jacks, relays, potentiometers, TV spin modulation tracks, electronic tuner base, rheostat parts, heat sensitive resistors, semiconductor thermometers, fine-tune the compensation capacitors, filters, disk drives, transformers, large-scale switch, bobbin, distributor, good as stents.
PPS in the application of household appliances: uranium and a variety of starter parts, adjust back to the turntable, a variety of rails, throttle cover, within the insulated part of electromagnetic conditioner, hair dryer, iron parts, humidifier water container, dry made frame, the pressure cooker lid, typewriters and copier parts, washing machine gear, heater outlet and heats the surrounding parts, machine parts in clothing.

Read more: Buy A PPS R7

The Introduction of 100P POM

100P is a heights viscousness acetal homopolymer because consumption in easily to fulfill forges. 100P brings home the bacon upper limit huskiness inward the line of product without alteration. 100P bears meliorated litigating thermic constancy.
Features: POM (POM) as a white opaque, a no-side-chain of high-density, high crystallinity of the linear polymer has good overall performance, outstanding fatigue resistance and excellent creep resistance, good electrical properties.
  

1. Mechanical Properties: As the POM is a highly crystalline polymer, has a high elastic modulus, high hardness and stiffness. Long-term use in the -40-100 ℃. And resistance to repeated impact, intensity, strength and temperature by the temperature change is small.
2. Thermal properties: POM has a high heat distortion temperature, were clustered into 136 ℃, copolymer of 110 ℃, but because of differences in molecular structure, but acetal copolymer has a higher continuous use temperature, in general, POM long-term effect temperature is 100 ℃, while the acetal copolymer can continue to use the 114 ℃ 2000h, or at 138 ℃ continuous use 1000h. short-term use of up to 160 ℃.
3. Chemical Resistance: The basic structure of POM it is not solvent at room temperature, below the melting point at or near the resin, but also almost no solvents, only few substances, such as perfluorinated C copper, to form a very dilute solution. So in all POM-resistant engineering plastics in organic solvents and oil resistance is very conspicuous. Especially in high temperature conditions are very good corrosion resistance, mechanical strength and size, and little change.
4. Electrical performance: good electrical properties of POM is one of the dielectric constant, independent of temperature and humidity. Different manufacturing process lead to differences in levels of trace impurities in the volume resistance can be brought for an order of magnitude of impact.
5. POM performance deficiencies; the relative density of large, opaque, not acid; molding shrinkage rate is high; melting point of not very high; thermal degradation at high temperatures very rapidly. In the presence of oxygen thermal oxidative degradation also occurs.

Usage: stress components, processing material, plate, bar, tube.


Read more: Buy A 100P POM

Where to get PP 500P

PP 500P is a culture medium catamenia, useful class because bulge and injectant mouding coverings.PP 500P can be used for producing woven bags, flexible intermediate bulk containers, ropes &twines, carpet backing, geotextiles and concrete reinforcements. PP 500P is suitable for Food contact application. Detailed information is provided in relevant Material Safety Datasheet and for additional specific information please contact SABIC local representative for certificate.

PP resin should be stored to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably don’t exceed 50°C. If applied for extrusion this grade shows an excellent stretchability and is therefore particularly suitable for tapes and strapping, high tenacity yarns and carpet backing. For thermoforming it shows an unique balance between transparancy, impact resistance and thickness uniformity. For injection moulded articles it is mainly used for caps and closures and houseware products, where this grade shows a high stiffness, combined with a fair impact resistance and very good surface hardness.SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PP resin within 6 months after delivery. Polyolefins are a family derived from propylene and ethylene polymers can be used to produce large amounts of thermoplastic products, and has many different uses high-strength, flexible plastic products. As research and technology, increasing the types of polyolefin materials, in many purposes are gradually replacing traditional materials. In addition, the polyolefin most easy to recycle. Main features: fiber, filament and tape extrusion – homopolymer. Uses: tight bags, containers, rope and winding, carpet lining, geotextiles, etc.

PP 500P is specially developed for producing stretched tapes with following features.

• Consistent processability
• Easy orientation
• Low water carry over
• Good mechanical properties

Read more: Buy A PP 500P

The Advantages of MF001 PMMA

MF001 PMMA colorless transparent glass-like, the proportion of 1.19, a lower surface hardness, hard objects can easily be scratched. Difficult to fire, but it can slow-burning, from the fire could continue burning, burning easily cracked, melted dripping, flame bright, blue bottom, white top, and send a strong floral smell rotting vegetables smell.
Performance
1. Transparency: MF001 PMMA are amorphous polymers, the internal molecular arrangement of the light will not interfere with access to its passage in various parts of the speed of light, which can all move the same speed (ie, a uniform refractive index), did not surrounded by scattered light will interfere with each other. Therefore, PMMA has good optical performance, high light transmission rate (90 ~ 92%, and wavelength). Extremely smooth surface film or bar, in the bend to a certain extent can also be injected into the light from one end of all progress in its internal reflection, the last shot from the other side, as if the water flow through the pipe as in (a certain curvature is the position after bending into the original position of the point of view, can not exceed 42 °; bending curved, the curved rod diameter or radius must be greater than three times the sheet thickness). But when sanding the surface of a part of the light can escape from here and show light. This feature can be used to create edge-emitting devices, surgical appliances.
2. Mechanical properties: MF001 PMMA mechanical strength than ordinary glass, more than 10 times higher, but compared to other plastics can only be considered moderate strength. The disadvantage is that the quality Qing Cui, easy to crack (or appear crazes), low surface hardness, easily scratched and dull; poor wear resistance, the coefficient of static friction between them is 0.8, the dynamic friction coefficient of steel is 0.45 ~ 0.50, so easy to scratch sanding.
3. Electrical properties: PMMA is a good electrical properties, especially in the low-frequency operating conditions. However, some of its unique electrical properties: the dielectric loss tangent with frequency increases. Influence of temperature and frequency dielectric constant, while the climate and humidity has little effect on the electrical properties. However, electrical properties than PE, PS arithmetic.
Features: excellent mobility, for large or thin molded products; acrylic grain processing generally can extrusion injection molding or compression molding, the molding temperature of about 170 ~ 240 ° C; PMMA is a colorless, transparent, transmission rate is the best plastic than glass high, the light through the range; reflectivity with the angle of incidence and change, there is light absorption is small, do total reflection. MF001 PMMA is light, tough, at room temperature under high mechanical strength, but also by the temperature effect is small, only when close to the softening point of strength and Tg only when a sharp decline; excellent surface gloss, tinting strength, good dimensional stability, but the surface trace of hardness and anti-poor, low impact strength, good electrical properties, but decreased with increasing frequency, low water absorption, resistance to water-soluble inorganic salts and some acid, and long-chain alkanes, ethers, fats, oils, not alkali; anti-aging, non-toxic, non-burning flame;
Uses: can be used for aviation, aerospace, automobile, ship bulletproof glass, window glass, instrument accessories, take cover, lights, light, optical instruments, such as glasses, magnifying glass and a variety of lenses. Construction materials such as color plates, high decorative materials, furniture, partitions. orthopedic medical devices such as artificial limbs, nose, eyes, medical light pipe, denture powder. stationery, household Lu, such as pen, drawing tools, teaching models, specimens, fixtures, buttons, hair clips, candy dish, etc..

Read more: Buy A MF001 PMMA

where to get VH001 PMMA

VH001 PMMA has the best heat resistance, weather resistance. For vehicles, lighting, optical products. MF001 Nantong Rayon, has excellent mobility, for large or thin molded product molded products. Main uses: grocery, household appliances lighting.VH001 resistance of acrylic company long-term supply polyester butyl acetate PBT terephthalic acid. The company business PMMA Germany evonik degussa 6 N, quality assurance.

1. Supply PMMA Taiwan chi mei high liquidity CM-211; Heat resistant level CM-205; General level CM-207;
2. Supply PMMA zhenjiang chi mei CM-211, 205- CM, CM-207;
3. Supply PMMA Korean LG IF850 general level, IG840, EH910, EF940;
4. Ruby colour, supply PMMA British general level CP-51 A, CP-61 A, CP-81 A;
5. Supply PMMA arkema thermal resistance V150, V020; High temperature resistant V040 excellent wear resistance, V825;
6. Supply PMMA nantong li Yang impact resistance general level MF001; Heat resistance of climate resistance VH001; Setting the level TF8, VH5; IRD70, MD001, VH150
7. Japan’s sumitomo supply PMMA resistance to impact HT55X; Heat resistance MH; LG2, LG, TH50Y;
8. Supply PMMA Japan as a climatic 560 F into resistance; Injection class 80 N;
9. Supply PMMA mitsubishi li Yang impact resistance VRL40; Setting the level TF8, VH5; Heat resistance of climate resistance VH001; High IRH70 blunt, IRD70, MD001,
10. Supply PMMA Germany degussa 5 N, 7 N, 8 N, 7 H, 7 M, 8 H, 8 NDF23.
11. Supply PMMA ebon T-80 Taiwan

Properties: FeiJingTi polymer, 92% light transmittance, the thermal denaturation temperature between 74 ° C ~ 102 ° C in between.
Advantages: 1, highlights learn transparency; 2, good cold; 3, better rigidity; 4, easy dyeing.
USES: chimney, window, sign, optical lens, hard contact lenses, car parts.


Read more: Buy A VH001 PMMA

The Features of LDPE FB3000

LDPE FB3000 is mainly used for transparent bag, film, car packaging, heavy bags, shrinkage filmDegree of low-density polyethylene polyethylene (LDPE) is a plastic material, it is suitable for a variety of molding thermoplastic molding process, forming good. LDPE mainly used for thin-film products, but also for the injection molding products, medical devices, pharmaceutical and food packaging materials, blow molding products.
Linear low density polyethylene (LDPE FB3000), ethylene and a small amount of high-level α-olefins (such as butene, hexene, octene-1, four methyl pentene-1, etc.) in the catalyst, the high or low pressure polymerization of a copolymer, the density is 0.915 ~ 0.940 g / cc between. However, according to the ASTM D-1248-84 provisions, 0.926 ~ 0.940 g / cc density range is a medium density polyethylene (MDPE). A new generation of LLDPE density expanded to its plastic body (0.890 ~ ​​0.915 g / cc) and elastomers (<0.890 g / cc). But the U.S. Plastics Industry Association (SPI) and the U.S. Plastics Industry Council (APC) will only extend the scope of LDPE FB3000, not including elastomers. The 1980s, Union Carbide and Dow Chemical Company to its early sales of plastic and elastomer called very low density polyethylene (VLDPE) and ultra low density polyethylene (ULDPE) resin. General molecular structure of LLDPE is characterized by its linear main chain, only a few or no long-chain branching, but contains some of the short branched-chain. No long-chain branching to higher crystallinity of the polymer. Typically, LLDPE resin density and melt index to characterize. Density of the polymer chain, the concentration of comonomer decision. Comonomer in the polymer concentration determines the amount of short branched-chain. Short chain length depends on the type of comonomer. The higher the concentration of comonomer, the lower the density of the resin. In addition, the average molecular weight of the resin melt index is reflected mainly by the reaction temperature (solution method) and adding chain transfer agent (gas phase) to decide. Independent of molecular weight and molecular weight distribution, which mainly affected by the catalyst type. LLDPE in the 1970s by the Union Carbide Corporation of industrialization, it represents a polyethylene catalyst and process technology a major change, to make polyethylene significantly expanded range of products. LLDPE with a complex catalyst instead of free radical initiator, and a lower cost of low-pressure gas to replace higher-cost high-pressure polymerization reactor, in a relatively short period of time, then its superior performance and lower cost, in many field has been replaced by LDPE. Currently LLDPE into almost all of the traditional polyethylene market, including film, molding, pipe and wire and cable. LLDPE products non-toxic, tasteless, odorless, milky white particles. Compared with LDPE high strength, toughness, rigidity, heat, cold, etc., also has good resistance to environmental stress cracking resistance, tear strength and other properties, and acid, alkali, organic solvent. In 2005, China’s LLDPE production is 188 million tons, accounting for 35.5% of total PE; consumption of 3.55 million tons, accounting for PE 33.8% of total consumption. The next 2 to 3 years, LLDPE consumption will remain around 8% rate of continued growth. According to the current market price of 12,000 yuan / ton, the market size of China’s LLDPE has more than 400 billion yuan.

Read more: Buy A LDPE FB3000

The Features of LG2 PMMA

PMMA (polymethyl methacrylate) English name: PolymethylMethacrylate. PMMA resin is non-toxic and environmentally friendly material that can be used to produce tableware, sanitary ware, etc., have good chemical stability, and weatherability. PMMA resin is not easy to produce sharp in broken fragments, the United States, Japan and other countries and regions have been made ​​mandatory in the law, schools and kindergartens architectural glass must be used PMMA resin. At present, all over the country to speed up the pace of urban construction, street signs, advertising light boxes and telephone booths, large numbers, in which a considerable portion of the material used is PMMA resin. Beijing Olympic project building outdoor color green also makes extensive use of PMMA resin.Gather methyl methacrylate (mma), with acrylic acid and its ester polymerization of acrylic polymer referred to get such tree ester, corresponding plastic collectively polyethylene acid plastic, among them with poly (methyl propylene methyl ester most widely used. Gather methyl methacrylate (mma) abbreviation code PMMA, plexiglass, is by far the most transparent material texture synthesis of excellent, price and more suitable varieties. Application: PMMA soluble in organic solvent, such as phenol, benjia ethers, through the spin coating can form a good film, has the good dielectric properties, as there is an airport effect tube (OFET) is also called the organic thin-film transistors (OTFT) medium layer.

Typical Applications
Automotive industry (equipment, lights, instrument panel, etc.), pharmaceutical industry (blood storage containers, etc.), industrial applications (DVD, light scattering device), key electronic products (especially transparent). Consumer goods (beverage cups, stationery, etc.). PMMA dissolved in organic solvents, such as phenol, anisole, etc., can be formed by spin-coating a good film with good dielectric properties, can be used as organic field effect transistor (OFET), also known as organic thin film transistor (OTFT) dielectric layer .
Chemical and Physical Properties

PMMA has good optical properties and resistance to climate change features. White light penetrating up to 92%. PMMA products with very low birefringence, particularly suitable for making VCDs. PMMA has a room temperature creep. As the load increased, the time growth can lead to stress cracking phenomenon. PMMA has good impact properties. As the PMMA surface hardness is not high, easy to clean hair, low-impact resistance, molding defects and poor flow properties, PMMA modified one after another. Such as methyl methacrylate and styrene butadiene copolymer, PMMA and PC blends and so on. Super transparent PMMA material mainly used for mobile protection screen, the product is divided into a hardening coating, without curing the coating two. It features excellent light transmission rate, impurities, electrostatic protective film, the surface hardness after hardening up thick 5-6H above present especially recommended for hardening of the PMMA material, the domestic as health board.

Read more: Buy A LG2 PMMA

The Introduction of MF001 PMMA

MF001 PMMA colorless transparent glass-like, the proportion of 1.19, a lower surface hardness, hard objects can easily be scratched. Difficult to fire, but it can slow-burning, from the fire could continue burning, burning easily cracked, melted dripping, flame bright, blue bottom, white top, and send a strong floral smell rotting vegetables smell.
Performance
1. Transparency: MF001 PMMA are amorphous polymers, the internal molecular arrangement of the light will not interfere with access to its passage in various parts of the speed of light, which can all move the same speed (ie, a uniform refractive index), did not surrounded by scattered light will interfere with each other. Therefore, PMMA has good optical performance, high light transmission rate (90 ~ 92%, and wavelength). Extremely smooth surface film or bar, in the bend to a certain extent can also be injected into the light from one end of all progress in its internal reflection, the last shot from the other side, as if the water flow through the pipe as in (a certain curvature is the position after bending into the original position of the point of view, can not exceed 42 °; bending curved, the curved rod diameter or radius must be greater than three times the sheet thickness). But when sanding the surface of a part of the light can escape from here and show light. This feature can be used to create edge-emitting devices, surgical appliances.
2. Mechanical properties: MF001 PMMA mechanical strength than ordinary glass, more than 10 times higher, but compared to other plastics can only be considered moderate strength. The disadvantage is that the quality Qing Cui, easy to crack (or appear crazes), low surface hardness, easily scratched and dull; poor wear resistance, the coefficient of static friction between them is 0.8, the dynamic friction coefficient of steel is 0.45 ~ 0.50, so easy to scratch sanding.
3. Electrical properties: PMMA is a good electrical properties, especially in the low-frequency operating conditions. However, some of its unique electrical properties: the dielectric loss tangent with frequency increases. Influence of temperature and frequency dielectric constant, while the climate and humidity has little effect on the electrical properties. However, electrical properties than PE, PS arithmetic.
Features: excellent mobility, for large or thin molded products; acrylic grain processing generally can extrusion injection molding or compression molding, the molding temperature of about 170 ~ 240 ° C; PMMA is a colorless, transparent, transmission rate is the best plastic than glass high, the light through the range; reflectivity with the angle of incidence and change, there is light absorption is small, do total reflection. MF001 PMMA is light, tough, at room temperature under high mechanical strength, but also by the temperature effect is small, only when close to the softening point of strength and Tg only when a sharp decline; excellent surface gloss, tinting strength, good dimensional stability, but the surface trace of hardness and anti-poor, low impact strength, good electrical properties, but decreased with increasing frequency, low water absorption, resistance to water-soluble inorganic salts and some acid, and long-chain alkanes, ethers, fats, oils, not alkali; anti-aging, non-toxic, non-burning flame;
Uses: can be used for aviation, aerospace, automobile, ship bulletproof glass, window glass, instrument accessories, take cover, lights, light, optical instruments, such as glasses, magnifying glass and a variety of lenses. Construction materials such as color plates, high decorative materials, furniture, partitions. orthopedic medical devices such as artificial limbs, nose, eyes, medical light pipe, denture powder. stationery, household Lu, such as pen, drawing tools, teaching models, specimens, fixtures, buttons, hair clips, candy dish, etc..

Read more: Buy A MF001 PMMA

The Features of VH001 PMMA

 

VH001 PMMA has the best heat resistance, weather resistance. For vehicles, lighting, optical products. MF001 Nantong Rayon, has excellent mobility, for large or thin molded product molded products. Main uses: grocery, household appliances lighting.VH001 resistance of acrylic company long-term supply polyester butyl acetate PBT terephthalic acid. The company business PMMA Germany evonik degussa 6 N, quality assurance.

1. Supply PMMA Taiwan chi mei high liquidity CM-211; Heat resistant level CM-205; General level CM-207;
2. Supply PMMA zhenjiang chi mei CM-211, 205- CM, CM-207;
3. Supply PMMA Korean LG IF850 general level, IG840, EH910, EF940;
4. Ruby colour, supply PMMA British general level CP-51 A, CP-61 A, CP-81 A;
5. Supply PMMA arkema thermal resistance V150, V020; High temperature resistant V040 excellent wear resistance, V825;
6. Supply PMMA nantong li Yang impact resistance general level MF001; Heat resistance of climate resistance VH001; Setting the level TF8, VH5; IRD70, MD001, VH150
7. Japan’s sumitomo supply PMMA resistance to impact HT55X; Heat resistance MH; LG2, LG, TH50Y;
8. Supply PMMA Japan as a climatic 560 F into resistance; Injection class 80 N;
9. Supply PMMA mitsubishi li Yang impact resistance VRL40; Setting the level TF8, VH5; Heat resistance of climate resistance VH001; High IRH70 blunt, IRD70, MD001,
10. Supply PMMA Germany degussa 5 N, 7 N, 8 N, 7 H, 7 M, 8 H, 8 NDF23.
11. Supply PMMA ebon T-80 Taiwan

Properties: FeiJingTi polymer, 92% light transmittance, the thermal denaturation temperature between 74 ° C ~ 102 ° C in between.
Advantages: 1, highlights learn transparency; 2, good cold; 3, better rigidity; 4, easy dyeing.
USES: chimney, window, sign, optical lens, hard contact lenses, car parts.




Read more: Buy A VH001 PMMA

How to Buy M90-04 POM

M90-04 POM as a milky white opaque, a no-side-chain of high-density, high crystallinity of the linear polymer has good overall performance, outstanding fatigue resistance and excellent creep resistance, good electrical properties, etc. .
      

1.         Mechanical Properties: As the POM is a highly crystalline polymer, has a high elastic modulus, high hardness and stiffness. Long-term use in the -40-100 ℃. And resistance to repeated impact, intensity, strength and temperature by the temperature change is small.

2.         Thermal properties: POM has a high heat distortion temperature, were clustered into 136 ℃, copolymer of 110 ℃, but because of differences in molecular structure, but acetal copolymer has a higher continuous use temperature, in general, POM long-term effect temperature is 100 ℃, while the acetal copolymer can continue to use the 114 ℃ 2000h, or at 138 ℃ continuous use 1000h. short-term use of up to 160 ℃.

3.         Chemical Resistance: The basic structure of POM it is not solvent at room temperature, below the melting point at or near the resin, but also almost no solvents, only few substances, such as perfluorinated C copper, to form a very dilute solution. So in all POM-resistant engineering plastics in organic solvents and oil resistance is very conspicuous. Especially in high temperature conditions are very good corrosion resistance, mechanical strength and size, and little change.

4.         Electrical performance: good electrical properties of POM is one of the dielectric constant, independent of temperature and humidity. Different manufacturing process lead to differences in levels of trace impurities in the volume resistance can be brought for an order of magnitude of impact.

5.         POM performance deficiencies; the relative density of large, opaque, not acid; molding shrinkage rate is high; melting point of not very high; thermal degradation at high temperatures very rapidly. In the presence of oxygen thermal oxidative degradation also occurs.

Uses

1.the automobile industry: manufacture of automotive pump, carburetor parts, pipelines, power valve, universal joint bearing, motor gears, crank, handlebars, instrument panels, automotive window lift equipment, electrical switches, safety buckle and so on.
2. Machinery manufacturing industry: widely used application of gears, shafts, chains, valves six, stem nut, bearings, convex l wheel, impeller, roller, nozzle, guide, bushings, fittings, and mechanical and structural parts transmission parts.
3. Electrical and electronics, home appliances field; manufacture plugs, switches, buttons, relays, washing machine pulley, shaft and wheel cassette shell, computer housings and televisions, washing machines, refrigerators, telephones, tape recorders, the dish washer various parts.
4. Precision instruments: the manufacture of the shelf support frame, cover the body, the friction plate and watches, cameras, other precision instruments, parts’
5. POM from time to time can be used for corrosion resistance of fire hoses, pencil pen and pen, toys, comb, zipper, mascara sticks and other consumer goods, and so on.

More aout: M90-04 POM for sale

The Introduction of PP 500P

PP 500P is a culture medium catamenia, useful class because bulge and injectant mouding coverings.PP 500P can be used for producing woven bags, flexible intermediate bulk containers, ropes &twines, carpet backing, geotextiles and concrete reinforcements. PP 500P is suitable for Food contact application. Detailed information is provided in relevant Material Safety Datasheet and for additional specific information please contact SABIC local representative for certificate.

PP resin should be stored to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably don’t exceed 50°C. If applied for extrusion this grade shows an excellent stretchability and is therefore particularly suitable for tapes and strapping, high tenacity yarns and carpet backing. For thermoforming it shows an unique balance between transparancy, impact resistance and thickness uniformity. For injection moulded articles it is mainly used for caps and closures and houseware products, where this grade shows a high stiffness, combined with a fair impact resistance and very good surface hardness.SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PP resin within 6 months after delivery. Polyolefins are a family derived from propylene and ethylene polymers can be used to produce large amounts of thermoplastic products, and has many different uses high-strength, flexible plastic products. As research and technology, increasing the types of polyolefin materials, in many purposes are gradually replacing traditional materials. In addition, the polyolefin most easy to recycle. Main features: fiber, filament and tape extrusion - homopolymer. Uses: tight bags, containers, rope and winding, carpet lining, geotextiles, etc.

PP 500P is specially developed for producing stretched tapes with following features.

• Consistent processability
• Easy orientation
• Low water carry over
• Good mechanical properties

Read more: Buy A PP 500P

The Advantages of LG2 PMMA

PMMA (polymethyl methacrylate) English name: PolymethylMethacrylate. PMMA resin is non-toxic and environmentally friendly material that can be used to produce tableware, sanitary ware, etc., have good chemical stability, and weatherability. PMMA resin is not easy to produce sharp in broken fragments, the United States, Japan and other countries and regions have been made ​​mandatory in the law, schools and kindergartens architectural glass must be used PMMA resin. At present, all over the country to speed up the pace of urban construction, street signs, advertising light boxes and telephone booths, large numbers, in which a considerable portion of the material used is PMMA resin. Beijing Olympic project building outdoor color green also makes extensive use of PMMA resin.Gather methyl methacrylate (mma), with acrylic acid and its ester polymerization of acrylic polymer referred to get such tree ester, corresponding plastic collectively polyethylene acid plastic, among them with poly (methyl propylene methyl ester most widely used. Gather methyl methacrylate (mma) abbreviation code PMMA, plexiglass, is by far the most transparent material texture synthesis of excellent, price and more suitable varieties. Application: PMMA soluble in organic solvent, such as phenol, benjia ethers, through the spin coating can form a good film, has the good dielectric properties, as there is an airport effect tube (OFET) is also called the organic thin-film transistors (OTFT) medium layer.

Typical Applications
Automotive industry (equipment, lights, instrument panel, etc.), pharmaceutical industry (blood storage containers, etc.), industrial applications (DVD, light scattering device), key electronic products (especially transparent). Consumer goods (beverage cups, stationery, etc.). PMMA dissolved in organic solvents, such as phenol, anisole, etc., can be formed by spin-coating a good film with good dielectric properties, can be used as organic field effect transistor (OFET), also known as organic thin film transistor (OTFT) dielectric layer .
Chemical and Physical Properties

PMMA has good optical properties and resistance to climate change features. White light penetrating up to 92%. PMMA products with very low birefringence, particularly suitable for making VCDs. PMMA has a room temperature creep. As the load increased, the time growth can lead to stress cracking phenomenon. PMMA has good impact properties. As the PMMA surface hardness is not high, easy to clean hair, low-impact resistance, molding defects and poor flow properties, PMMA modified one after another. Such as methyl methacrylate and styrene butadiene copolymer, PMMA and PC blends and so on. Super transparent PMMA material mainly used for mobile protection screen, the product is divided into a hardening coating, without curing the coating two. It features excellent light transmission rate, impurities, electrostatic protective film, the surface hardness after hardening up thick 5-6H above present especially recommended for hardening of the PMMA material, the domestic as health board.

Read more: Buy A LG2 PMMA

The Advantages of VH001 PMMA

VH001 PMMA has the best heat resistance, weather resistance. For vehicles, lighting, optical products. MF001 Nantong Rayon, has excellent mobility, for large or thin molded product molded products. Main uses: grocery, household appliances lighting.VH001 resistance of acrylic company long-term supply polyester butyl acetate PBT terephthalic acid. The company business PMMA Germany evonik degussa 6 N, quality assurance.

1. Supply PMMA Taiwan chi mei high liquidity CM-211; Heat resistant level CM-205; General level CM-207;
2. Supply PMMA zhenjiang chi mei CM-211, 205- CM, CM-207;
3. Supply PMMA Korean LG IF850 general level, IG840, EH910, EF940;
4. Ruby colour, supply PMMA British general level CP-51 A, CP-61 A, CP-81 A;
5. Supply PMMA arkema thermal resistance V150, V020; High temperature resistant V040 excellent wear resistance, V825;
6. Supply PMMA nantong li Yang impact resistance general level MF001; Heat resistance of climate resistance VH001; Setting the level TF8, VH5; IRD70, MD001, VH150
7. Japan’s sumitomo supply PMMA resistance to impact HT55X; Heat resistance MH; LG2, LG, TH50Y;
8. Supply PMMA Japan as a climatic 560 F into resistance; Injection class 80 N;
9. Supply PMMA mitsubishi li Yang impact resistance VRL40; Setting the level TF8, VH5; Heat resistance of climate resistance VH001; High IRH70 blunt, IRD70, MD001,
10. Supply PMMA Germany degussa 5 N, 7 N, 8 N, 7 H, 7 M, 8 H, 8 NDF23.
11. Supply PMMA ebon T-80 Taiwan

Properties: FeiJingTi polymer, 92% light transmittance, the thermal denaturation temperature between 74 ° C ~ 102 ° C in between.
Advantages: 1, highlights learn transparency; 2, good cold; 3, better rigidity; 4, easy dyeing.
USES: chimney, window, sign, optical lens, hard contact lenses, car parts.



Read more: Buy A VH001 PMMA

How to Buy F30-03 POM

F30-03 POM is mianly for engineering products for general use.POM (English: polyformaldehyde) crystalline thermoplastic polymer. Known as the “super steel” or “race of steel”, also known as polyoxyethylene methyl. Structure, the English abbreviation for the POM. Usually derived from the polymerization of formaldehyde polymer, the degree of polymerization is not high, and the vulnerable thermal depolymerization.
POM is a no side-chain, high-density, high-crystalline linear polymer with excellent performance. POM is a smooth, shiny, hard and dense material, yellow or white, in the -40-100 ° C temperature range, long-term use. Its wear resistance and self-lubricating plastic is superior than most, and good oil resistance, peroxides performance. Very acid, alkali and intolerance intolerant solar ultraviolet radiation. POM tensile strength 70MPa, water absorption, dimensional stability, glossy, the good performance than nylon, POM is a highly crystalline resin, the thermoplastic resin is the toughest. With thermal strength, flexural strength, fatigue resistance of high intensity, abrasion resistance and excellent electrical properties.
General synthesis of POM aqueous solution of formaldehyde in the presence of acid condensation polymerization. Received more than 100 degree of polymerization of a-POM, and then broken down into formaldehyde gas heated by the refined and dehydration, often using some of the pre-polymerization of purified monomer, and then pass into the initiator containing a small amount of solvent in the dry polymerization. Because of the presence of water, so that a significant reduction in molecular weight. Initiator can be a Lewis acid or alkali. But most of the anion with tertiary amine addition polymerization, the reaction is as follows: POM acetal end groups of a half (-CH2OH), when the temperature is higher than 100 ℃, end-easy to break, the general subject that the stability of end-processing of. Stabilization can be heat treated to 230 ℃. Paraformaldehyde in 170 ~ 200 ℃ temperature processing, such as injection, extrusion, blow molding, etc. Mainly used for engineering plastics for the automotive, mechanical parts and so on.
Polyoxymethylene (pom) is an excellent engineering plastics, in foreign countries have “wins Steel”, “2 POM products.
Super steel, “said. Pom with similar metal hardness, strength and rigidity, in a wide range of temperature and humidity have a good self-lubricating, good fatigue resistance, and resilient, it also have better chemical resistance. pom below the cost of many other engineering plastics, is replacing some of the traditionally occupied by the metal markets, such as alternative zinc, brass, aluminum and steel production in many parts, since its inception, pom has been widely used in electrical and electronic, mechanical, instrumentation, daily light industry, automobile, building materials, agriculture and other areas in many new areas of applications such as medical technology, sports equipment, etc., pom also showed good growth .



Read more:F30-03 POM for sale

How to Buy PEI 1000

PEI 1000, combined with advanced polymers show an excellent thermal , mechanical and electrical properties , together with low flammability and low smoke evolution during combustion . These features make the 1000 ideal for Pei electrical / electronic insulators and for many components , high strength, rigidity requires a higher temperature .

PEI gas release is low, can be used for aircraft / aerospace industry internal documents PEI 1000-7101: PEI is the chemical structure of aromatic amide and ether sub- unit formed on the basis of repetition , are stable for many chemicals , such as the vast majority of hydrocarbons, alcohols , all halogenated solvents, halogenated solvents dissolve special . PEI 1000-7101: PEI glass fiber , carbon fiber or other fillers can be modified to enhance the purpose .

 

 

 

Read more: PEI 1000 for sale

The Introduction of M90-04 POM

M90-04 POM as a milky white opaque, a no-side-chain of high-density, high crystallinity of the linear polymer has good overall performance, outstanding fatigue resistance and excellent creep resistance, good electrical properties, etc. .
      

1.         Mechanical Properties: As the POM is a highly crystalline polymer, has a high elastic modulus, high hardness and stiffness. Long-term use in the -40-100 ℃. And resistance to repeated impact, intensity, strength and temperature by the temperature change is small.

2.         Thermal properties: POM has a high heat distortion temperature, were clustered into 136 ℃, copolymer of 110 ℃, but because of differences in molecular structure, but acetal copolymer has a higher continuous use temperature, in general, POM long-term effect temperature is 100 ℃, while the acetal copolymer can continue to use the 114 ℃ 2000h, or at 138 ℃ continuous use 1000h. short-term use of up to 160 ℃.

3.         Chemical Resistance: The basic structure of POM it is not solvent at room temperature, below the melting point at or near the resin, but also almost no solvents, only few substances, such as perfluorinated C copper, to form a very dilute solution. So in all POM-resistant engineering plastics in organic solvents and oil resistance is very conspicuous. Especially in high temperature conditions are very good corrosion resistance, mechanical strength and size, and little change.

4.         Electrical performance: good electrical properties of POM is one of the dielectric constant, independent of temperature and humidity. Different manufacturing process lead to differences in levels of trace impurities in the volume resistance can be brought for an order of magnitude of impact.

5.         POM performance deficiencies; the relative density of large, opaque, not acid; molding shrinkage rate is high; melting point of not very high; thermal degradation at high temperatures very rapidly. In the presence of oxygen thermal oxidative degradation also occurs.

Uses

1.the automobile industry: manufacture of automotive pump, carburetor parts, pipelines, power valve, universal joint bearing, motor gears, crank, handlebars, instrument panels, automotive window lift equipment, electrical switches, safety buckle and so on.
2. Machinery manufacturing industry: widely used application of gears, shafts, chains, valves six, stem nut, bearings, convex l wheel, impeller, roller, nozzle, guide, bushings, fittings, and mechanical and structural parts transmission parts.
3. Electrical and electronics, home appliances field; manufacture plugs, switches, buttons, relays, washing machine pulley, shaft and wheel cassette shell, computer housings and televisions, washing machines, refrigerators, telephones, tape recorders, the dish washer various parts.
4. Precision instruments: the manufacture of the shelf support frame, cover the body, the friction plate and watches, cameras, other precision instruments, parts'
5. POM from time to time can be used for corrosion resistance of fire hoses, pencil pen and pen, toys, comb, zipper, mascara sticks and other consumer goods, and so on.

More aout: M90-04 POM for sale